Replacement Handles for Crane Drexel.
The original Crane Drexel handles were made from Chrome plated zinc which over time corrodes. Until now, our only solution was to take handles that weren’t too badly ruined and re-chrome them. Customers with broken handles however, were out of luck.
  Finally, due to the numerous requests we’ve gotten for this style of handle, we’ve commissioned a production run of reproduction replacement Drexel handles, cast using an original as a pattern.

Porcelain Cross Crane Prewar Handles
While these reproduction handles aren’t quite identical to the original Crane handles, it sure beats throwing away a perfectly good pedestal sink for lack of handles. Fits either the 3/8” square stem or the 11/32” 12 point spline, and used in both tub/shower and widespread lavatory applications. Chrome spuds
86-090H Crane Hot porcelain handle 37.00
86-230C Crane Cold porcelain handle 37.00

Crane Porcelain Lavatory Escutcheon
At last! We’ve commissioned a run of replacement Crane porcelain escutcheons to go along with the above handles. They are a perfect color and shape match to the originals. They’re 2 7/16” wide at the base, and stand 2 3/16” tall with a 9/16” opening for the stem. Make your Crane lavatory sink look new again!
79-S293 Crane Lavy. escutcheon 40.00

Crane Dial-ese Repair kit.
Fits post-war Crane faucets up until the early 1960’s. Includes 2 sealing washers, 2 rubber bonnet washers, 2 stem O-rings, and 2 plastic handle inserts for Drexel and Canopy handles. One kit repairs 2 stems. Yes, our kit is more expensive than others out there on the web. It’s because we supply the correct washer that will actually work rather than the incorrect parts that many other companies have on the marketplace.
65-EK47 Dial-ese repair kit 12.95 
65-CHI Nylon handle inserts only, pair. 4.95

Large Crane Canopy Kitchen/Lavatory Handle
We finally found them!!!! Brilliant Chrome plating over zinc, these handles were thought to be unavailable. Not anymore! Fits Postwar Crane Kitchen faucets, and is also found in the occasional lavatory application. The original ones had “H” and “C” cast in the top of the wing, these do not. O.D. of handle is 2 1/16” with a height of 1 1/4”. Sold by the each.
80-1145D Crane large canopy handle 22.00

Crane Criterion Handle, Complete
Yes! After numerous requests, and a lot of searching, we’ve found a company reproducing the complete Criterion handle. The only other part available for this handle is the Lucite trim ring found below. Sorry, we haven’t found anyone selling the top cap by itself. It does, however, beat tearing out a tiled in sink when the only thing wrong is awful looking handles. Sold by the each. Make your Criterion sink look new today!
80-1123 Criterion handle, Each 72.00
80-1123P Criterion handle, Pair 119.00

Please note; you will have to remove and reuse the old street 45 that is attached to the bottom of your old valve body. We have not found a supplier of these and do not believe milled one are even being manufactured anymore...

We’re the only company currently reproducing parts for the Crane Drexel and Marcia integral spout faucets. Buy from the experts!!!!

Crane Chrome Dome

Crane Valve Body & Trim

Save that Crane Drexel or Marcia Sink with our new valve body and trim for sinks with the Integral Spout. Assembly includes chrome handle & trim, stem cartridge, valve body, and all washers. Sold by each, if needing both sides, please order two.
Crane Part Number F10697 

86-F97 Valve Body & Trim  $250.00

Our new dome fits the Dial-eze trim for the following sinks: Criterion, Diana, Drexel, Elayne, Marcia, Westland, and the 6inch center set Clermont. Combine this dome with new handles and add new life to your Crane Faucets. Made of solid brass, chrome plated unlike the chrome plated zinc domes of years past. 1-1/2” Diameter and ¾” High. 

86-F11619    Chrome Dome   29.00

Replacement Handle Ring for Criterion
Ring only for 1950’s to 1970’s Crane Criterion valves.
Measures 2-7/16” diameter x 3/4” high. Sold individually
20-24463 Criterion Handle Ring 35.00 each.
 

Locknuts for Crane Valve Bodies
 Locknut used on Crane integral spout hot and cold valve bodies. Also used on Prewar widespread lavatory valve bodies. I.D. 1 5/32” Sold singly.
86-F11585 Crane Valve Body Locknut. 18.00

Locknut used in post-war metal spout applications, does not fit on ceramic spout versions. I.D. 1 1/4”
86-550 Crane Valve Body Locknut. 18.00

Mixing Tube For Crane Spouts.
Crane spouts have a rigid, threaded tube running into the bottom of the spout on many models. It is very common for the threaded end of the tube to shear off during removal.

Small Canopy Handles for Crane
Fits Post-war 4” centerset lavatory sinks. Handles measure 2-3/4” long and stand 1-1/4” high. Fits 12 point 5/16” dia. stem. Chrome plate over heavy cast zinc. Note: does NOT replace Drexel or large kitchen canopy handle. Sold per each.
20-73387 Sm. Canopy Handle, Hot. 29.00
20-73395 Sm. Canopy Handle, Cold 29.00

Crane Retainer Ring for 4” Centerset Faucets
Another Score! Fits the above 20-73387 handles on many post-war 4” center lavatory faucets. We used to have to make these at $100 a pop... Chrome plate Brass, sold by the each. Note, NOT 1” pipe thread.... We still gotta make that one
80-0632 Crane Retainer ring 25.00

Supply Union for Crane PreWar Widespread Lavatories
Replaces lost or broken water supply union on Crane faucets. If you have a Crane valve with large male threads on the bottom and can’t figure out how to hook up the water supply lines, this is the part you are missing! 1/2” MIP x Crane union thread.
15-CRU Crane inlet union. 85.00 ea. 

Compression Adapter for Integral Spout
Concealed waterway sinks with 3/4” hole in the porcelain. (check holes, will not work in oversized or irregularly shaped holes.) New adapters machined using an original as a pattern. 1/2” OD stubs connect directly to original Crane valves or to flex lines with standard compression fittings (not included.)
15-CRCA Crane compression adapter 85.00 ea.

Sealing Washer for Crane Integral Spout Valve Bodies
Fits Drexel and other sinks with concealed waterway, seals valve body to porcelain. After years of attempting to cut our own gaskets for Crane integral spout sinks, we discovered these beveled washers that are nearly exact replacements for the original Crane washers.
 Please note, we said “nearly”, they’re not identical to the originals but have worked on every sink we’ve tried them on.
15-VBS Crane valve body seal, pair. 10.00

Washers above fit Crane sinks like this one with integral porcelain spouts.

Crane Dial-eze Bonnet Nuts, for Kitchen and Lavatory Valves
Fits Postwar Dial-eze valves, the taller one, (5/8” high) version is for Kitchen applications, the short (3/8” high) version is for Lavatory applications. Both measure 1 1/8” outside diameter and are chrome-plated Brass for extra durability!
86-F10716 Dial-eze Kitchen bonnet nut 10.80
86-F10584 Dial-eze Lavatory bonnet nut 8.00
 

Lavatory

New! Crane Dial-Eze Tub/Shower Trim Ring
After numerous requests, we’ve finally found one of these in good enough shape to duplicate, so we have. Flange measures 2 1/2” O.D. by 1 1/4” I.D. and is 1” high. The thread is the Crane “oddball” 16 T.P.I. Right now, we’re having to make these in small, hand-machined batches, so the price reflects that. If the demand is there, we’ll run a large batch....

Crane Pedestal Sink Brackets
Fits many others as well! Made of durable Stainless Steel, and designed to specifically fit Crane Pedestal sinks, these brackets are a copy of an original bracket. Will fit any sink that has holes at least 11/16” diameter and anywhere between 1” to 5” away from the wall. The slots cut in the back allow fine tuning when leveling the sink. Be sure to have at least 3” of depth in the sink to allow for the toggle. Bracket itself measures 5 3/4” long by 2” wide and sticks down 2 1/8”. Comes with everything shown and a set of directions.
59SB Sink bracket kit 29.95