Specialty

Check out our new
China high tank
Toilet
Click here!

	Home
	Site Index
	Original Antiques
	Tubs
	Showers
	Toilets
	Sinks
	Faucets
	Specialty Plumbing Parts
	Ceramic Accessories
	Door, Window & Cabinet Hardware
	Lighting
	Cleaners & Polishes
	Books
	Antique Keys & Locks
	Brass Decor & Bath Accessories
	Catalog Request
	About Us
	Ordering & shipping Information
	BARGAINS
	Touch & Flow Faucets
	Ifo Toilets & Parts
	Copper Sinks & Decor
	Crane Parts

Overstock Sale
on many of our
Polished Brass
Shower
Curtain
Rods!
Click Here!

High Tank Toilets	Low Tank Toilets	Toilet Seats
Toilet Bowls & Urinals	Toilet Parts	Specialty Toilet Parts
Stop Valves & Flanges	P-Traps & Drains	Gaylan Toilet parts

Toilet Parts Page 2: Flush tubes, seat bumpers, pull knobs & more!

Page 1: Tank parts, spuds, & flush levers.

Flush Ell for low tank toilets with tank mounted on the wall.
2" x 6" x 8" plated or polished brass 90 degree flush ell with matching slip-joint nuts & washers. May be cut to fit.
81-197 Coated Brass Flush Ell 90 degree 58.50
81-197C Chrome Flush Ell 90 degree 58.50
81-197N Nickel Flush Ell 90 degree 69.00

Extended Flush Ell for low tank toilets with an oddball rough-in application. Measures 2” x 8”x 10”, supplied with nuts and washers.
15-810B Polished uncoated brass Flush Ell 135.00
15-810LB Coated Brass Flush Ell 165.00
15-810N Polished nickel Flush Ell 185.00
15-810C Polished Chrome Flush Ell 195.00



		Top Spud Offset Flush Tube for low tank toilets with inlet hole in top of the bowl and tank mounted on wall offset flush ell, 2" Diameter x 1 1/2" offset x 6" tall with friction nuts & washers. . 73-39 Brass Top Spud Flush Tube 109.00 73-39C Chrome Top Spud Flush Tube 89.00 73-39N Nickel Top Spud Flush Tube 99.00


				Top-Spud “Oddball” Offset Flush Elbow 2” diameter, 6” tall, varying offsets. Supplied with nuts and slip-joint washers. These haven’t been made in years, and this is a limited production run. Used when top-spud tank and bowls don’t line up using the standard offset ell.

				2 1/2” offset in Raw Brass shown at left

	Raw Brass	Pol. Brass	Coat. Brass	Pol. Nickel	Chrome
3/4” offset	98.00	140.00	160.00	195.00	225.00
1” offset	98.00	140.00	160.00	195.00	225.00
2” offset	98.00	140.00	160.00	195.00	225.00
2 1/2” offset	98.00	140.00	160.00	195.00	225.00
3” offset	98.00	140.00	160.00	195.00	225.00

RARE MADDOX SPUD FOR TOP OR REAR SLOTTED SPUD HOLE TOILETS
Spud thread is 2 5/16" dia. and has two tabs that lock the spud in place. Spud length is 2". Complete with tapered rubber washer, brass friction ring, lock nut and 2" friction nut and washer.
24-MS Brass Maddux Spud, uncoated 85.00
24-MSB Brass Maddux Spud, lacquered 95.00
24-MSN Nickel plated brass Maddux Spud 120.00
(Standard spuds may be found on our Toilet Parts Page 1.)


	Pilltank Toilet Tank Cast Iron Bracket So, you found a wonderful old round toilet tank at the salvage yard, got it home, and went to install it and discovered that it required a special bracket that supported the tank through one hole in the

back of the tank. Until now, you were left with either having a custom bracket made, or giving up on the whole thing.... We too got tired of having to find these special brackets and had a run of them produced in Cast Iron. Bracket measures 13” long, and has a 5/8” pin protruding out of it. This is the pin that supports the pilltank. Screws not supplied, be sure to install support blocking in the wall!
19-940 Pilltank Bracket 69.00


	Replacement Flush & Fill tubes for High Tank toilets.


	76PIPE offset flush tube & 02-163 offset fill tube. Shown with seat bumper/support.


	02-161 straight fill tube & 81-628 flush ell shown. 24-98 pipe support pictured, sold separately

1 Pc. offset 1-1/2” O.D. flush tube. Heavy gauge .050 solid brass, 60” tall. Fits DEA 76-series high tank toilets and some older Gaylan toilets. Plain ends, no flange.
Finish:	Chrome	Uncoated pol. Brass	Lacquered Pol. Brass.	Pol. Nickel	Brush Nickel	Raw Brass
76PIPE (3.5” offset)	295.00	245.00	265.00	295.00	328.00	169.00
76PIPE-1 (1” offset)	295.00	245.00	265.00	295.00	328.00	169.00
76PIPE-2 (2” offset)	295.00	245.00	265.00	295.00	328.00	169.00
1-1/4” One Piece O.D. flush tube. .050 solid brass, 64” tall
76P1 (1” offset)	269.00	229.00	249.00	269.00	302.00	153.00
76P3 (3”offset)	269.00 Temp out	229.00 Temp out	249.00 Temp out	269.00 Temp out	302.00 Temp out	153.00 Temp out
Offset fill tube. 1/2” OD x 6’ offset fill tube. 4.25” offset at one end, 2.25” offset at the other. Matches the curves of 76-pipe fill tube above. Plain ends.
02163 offset fill tube	225.00	159.00	199.00	225.00	245.00	89.99
Straight Flush tube. 72” length. For use with top-spud bowls or with separate flush ell on rear-spud bowls. Seat bumper/support (sold below) recommended.
02161 1-1/4” OD, w/ flange	249.00	206.00	229.00	249.00	282.00	130.00
02162 1-1/2” OD, w/ flange	259.00	219.00	239.00	259.00	295.00	145.00
Straight Fill Tube. 1/2” OD x 6’, straight fill tube.Plain ends
02164 Straight fill tube.	195.00	130.00	170.00	195.00