Reconditioned faucets and valves offer a quality alternative to imports and can add an authentic touch to a vintage fixture. DEA rebuilt valves are inspected and restored to
new condition using modern materials. Reconditioned valves are guaranteed to be leak-free for 6 months from date of purchase. A nice feature of these older valves
is they use commonly available faucet washers and stem packing. Should your valve develop a leak years down the road, these time-tested and simple designs can be restored to
drip-free operation cheaply and easily..
1915 Speakman Ribcage Shower The ultimate shower! Ribcage showers were installed in the finest homes
and mansions near the turn of the century. This unit has a single control mixing valve that rivals any made today for sophistication. Four
separate diverter valves control the overhead rain showerhead, a handheld shower, the ‘wet’ ribs (ribs have tiny holes all the way around
spraying in towards the center), and the swing-out bidet fitting at the bottom.
Designed for installation in a tile enclosure with at least 12 GPM water supply and an 80 gal. water heater. (Definitely NOT a water saver!) Fits in a 38”
alcove, with 26 3/4” minimum opening and 32” from centerline of valve to center of riser. Requires extensive plumbing accomodations, for serious
restoration or antique plumbing enthusiasts only! Original nickel finish, unrestored. ORC0201 8200.00 as-is SOLD Fully restored in nickel: 19000.00
“Cleveland” Wall Tap Here’s something
different! Intended for gravity fed systems, this valve was actually made of white brass. When it’s polished, it looks just like Nickel, but does wear
off after 50 years or so... Handle appears to be Bakelite, inlet thread is actually 7/8” ballcock thread, so your plumber will have to get
creative.... Wall flange to centerline of outlet is 2 13/16” OF08301 Wall tap 295.00
Note on spout measurements: The length measurement on faucet spouts is taken from the center of the valve body to the center of the water outlet, it is not overall length of the whole faucet.
“Republic” Handle and Trim Set We’ve scored
again! We found quite a few sets of these ‘20’s vintage “Republic” handle sets while cleaning out a defunct plumbing supply. Original
stock, used, conditions vary, best goes first. This set came clean in less than 1 minute. OF0750 Sold out
We do also have several sets of extra escutcheons. Sold in sets, 1 3/4” tall, 3 3/16” O.D., 3/4” I.D. OF0751 40.00
“Standard” Keyhole Ceramic Cross Handle The rarest of the
rare! We usually do not get more than one of these at a time, and in our last expedition, we came up with a whole box of the little devils. 3 1/4” from
point to point, fits the 3/8” tapered “Standard” spline. WILL NOT fit the larger 7/16” tapered spline commonly found on
“Standard” shower valves. 8 available, varying conditions, best goes first, OF0752 “Standard” handle 75.00
Haws Drinking Fountain Completely original down to the Ceramic bubbler,
these styles of faucets are tough to find. This one has been fully replated in nickel, and is ready to install on 1/2” iron pipe. Extends out just
under 10”. One only, and it will not last! OF03100 Haws Bubbler 795.00
Morgan Cleveland Cowboy Tub Valves The rarest of the rare! Designed
for the cowboy tub, 1/2” I.P. inlets. We’re not sure of the exact date, but the type of tub these were made for hasn’t been produced for 100
years or so, so we’re figuring 1890’s. Fully restored and replated in polished nickel. We’re probably not going to see another pair of
these again... Grab them quick! OF07100 Tub Valves 300.00
Original Tub Overflow Covers w/ Logos Overflow covers were often embossed with the names of manufacturers and
plumbing companies. These are rare reconditioned originals. Wolverine Brass Works, Grand Rapids” Polished brass finish OTOC0500 65.00
“Edmund Grundy, Plumber” Replated in polished nickel, O.D. is
3 3/16”. OTOC08400 85.00
“Chas B. Huck, Buffalo, N.Y.” Replated in polished nickel, O.D.
is 3 1/16”. Custom made 100 years ago by Wolverine Brass OTOC08401 85.00
TUB OVERFLOW ADAPTOR KIT Convert trip lever to old-style chain and stopper
81-175AC Chrome plated 21.50 81-175AN Nickel plated 31.50 81-175ALB Polished coated brass 55.00
“Henry Huber Co. New York” Especially ornate, replated in
polished nickel. Overflow hole in tub must be at least 2 1/2” in diameter, O.D. of cover is 3 1/2” OTOC08402 105.00
“Hammond Plumbing Co. Hammond Ind.”
Replated in Polished nickel, O.D. of cover is 3 1/8”
.A bit rougher casting than the other three. OTOC08403 75.00
Call 800-255-4426 To order. Satisfaction 100% Guaranteed
Questions? Call us, our team of plumbing experts will help you select and connect your vintage faucet or valve.
